LIMITED TIME SAVE 15% off EFI Connection brand harnesses when purchasing CORE ECU! Simply add CORE ECU to your cart and then add any EFI Connection brand CORE engine harness. Savings will be shown in cart.
When an off-the-shelf genuine HP Tuners CORE engine harness assembly is not a direct fit for your CORE ECU installation, EFI Connection has you covered with the highest-quality engine harness assemblies for your CORE ECU installation.
ENGINE HARNESS CONNECTIONS
The following connections are included with this engine harness assembly...
SUPPORTED ECU: CORE ECU BY HP TUNERS
 |
This engine harness is for use with the CORE ECU by HP Tuners. The four AMP Super Seal 1.0 style connectors are used to make a connection to the CORE ECU. |
CRANK/CAM SIGNAL TYPE: 24X/1X
 |
The Crankshaft Position (CKP) Sensor connector on this harness is for use with all Gen III 24x LS CKP sensors. The early Gen IV LS2 engine also uses the 24x LS CKP sensor. |
 |
The Camshaft Position (CMP) Sensor connector on this harness is for use with all Gen III 1x LS CMP sensors. This sensor is located at the top rear/center of the engine behind the intake manifold. |
THROTTLE SYSTEM: DRIVE-BY-CABLE (DBC)
 
|
The throttle body connectors on this harness are for use with the 3-wire Throttle Position Sensor (TPS) and 4-wire Idle Air Control Motor (IAC) installed on all cable-driven LS style throttle bodies. This harness will not work with a Drive-by-Wire (DBW) throttle system. |
FUEL INJECTOR TYPE: EV1
 |
The fuel injector connectors on this harness are for use with EV1 style fuel injectors. GM used the EV1 fuel injectors on all production LS1 and LS6 engines. |
MAP SENSOR TYPE: DELPHI (EARLY LS ENGINES)
 |
The Manifold Absolute Pressure (MAP) sensor connector on this harness is for use with the early LS style Delphi MAP sensor. This sensor is commonly used with Gen III LS-Series engines. |
MAF SENSOR TYPE: LS3/LS7 SLOT/CARD
 |
The Mass Air Flow (MAF) sensor connector on this harness is for use with LS3/LS7 style MAF sensor. See our MAF Adapter Harnesses for CORE if you are using a different MAF sensor. MAF is not required, but an IAT breakout harness will be required for speed density operation. |
LAMBDA SENSOR TYPE: BOSCH LSU 4.9
 |
CORE ECU requires two Bosch LSU 4.9 wideband O2 (lambda) sensors. This harness provides a connection for bank 1 and bank 2 lambda sensors. |
EOP SENSOR TYPE: EARLY LS-SERIES
 |
The 3-wire Engine Oil Pressure (EOP) Sensor connector on this harness is for use with early EOP sensors. NOTICE! Single wire oil pressure sending units on certain LS engines are vehicle gauge cluster specific and not compatible with the GM PCM or CORE ECU. EOP is not required. |
KNOCK SENSOR TYPE: SINGLE WIRE RESONANT (TWO SENSORS)
 |
The Knock Sensor (KS) connector on this harness is for use with the knock sensor sub harness used with LS engines that have two 1-wire resonant type knock sensors located in the engine valley below the intake manifold. |
ALTERNATOR TYPE: 4-CAVITY LS-SERIES
 |
The alternator connector on this harness is for use with all 4-cavity LS alternators. Notice the single red wire is all that is needed to turn on the alternator. |
|
For 2 pin LS alternators, purchase our order-to-length adapter harness AWP-6042. from our Adapter Harnesses for CORE. |
ECT SENSOR TYPE: 2-WIRE LS-SERIES
 |
The Engine Coolant Temperature (ECT) sensor connector on this harness is for use all 2-wire ECT sensors. 1998 Camaro/Firebird LS1 engines will require the removal of the 3-wire ECT and replace with a 2-wire ECT sensor. |
TRANSMISSION TYPE: 4L60E | 4L65E | 4L70E
 |
This harness provides a direct connection to all 1996-newer 4L60E, 4L65E, and 4L70E transmissions. 1994 and 1995 4L60E transsmissions are electronically unique and not compatible with CORE ECU. |
VSS TYPE: LATE GM | ALL PRODUCTION LS
 |
The Vehicle Speed Sensor (VSS) connector on this harness is compatible with all factory GM LS style speed sensors. Conversions using an 80s or early 90s VSS will require an adapter harness sold separately. |
BARO TYPE: 1-BAR PACKARD/DELPHI STYLE
 |
CORE ECU supports the use of a Barometric Pressure (BARO) Sensor. We suggest the use of a RIFE 1-BAR BARO Sensor. BARO is not required. |
COMMUNICATION/DIAGNOSTIC LINK: RJ45 ETHERNET
 |
CORE ECU communicates with your Windows-based PC via an ethernet RJ45 connection cable. A tethered sealed dust cap is included. |
HPT NET SUPPORT: M8 CIRCULAR
 |
HPT Net support is included through the 22 AWG M8 cable assembly. |
CAN BUS SUPPORT: DEUTSCH/AMPHENOL DT SERIES CONNECTIONS
 |
CORE ECU has two CAN bus networks (in addition to HPT Net). Two 4-pin Deutsch/Amphenol style connectors are included for CAN bus expansion. A sealed cap is included for each CAN bus connector. |
ELECTRICAL CENTER: GM STYLE FUSE BLOCK ASSEMBLY
 |
The included electrical center is an OE style Aptiv bussed fuse block assembly containing ignition relay, fuel pump relay, fuses, and alternator 500 ohm resistor. Electrical center legend is laser engraved into the bottom of the included dust cap. |
100% FULL CONTINUITY TEST
 |
Every EFI Connection engine harness for CORE ECU is fully tested with our CIRRIS CR continuity testing unit. Mistakes are eliminated to ensure you receive our best possible work! |
ENGINE HARNESSES FOR CORE ECU
[CLICK HERE] for a complete list of LS-series engine wire harnesses for CORE ECU by engine configuration and transmission type. Choose from genuine HP Tuners and EFI Connection brand wire harnesses.
Designed and hand-crafted in Erie, PA by 